HOW TO CLEAN ELECTRIC SKATEBOARD WHEELS & BEARINGS

Electric skateboard is very popular nowadays. People are using it to ride around the city, do their shopping or have a joyride. However, other than riding an electric skateboard, you have to maintain it as well, in order to get better performance. A part of that maintenance is knowing how to clean Electric skateboard wheels & bearings. 

Today we will go over the details on how to clean electric skateboard wheels and bearings. Let’s start. 

How To Clean Electric Skateboard Wheels & Bearings: Tools You Need

In order to clean the wheels and bearings of your electric skateboard, you need some tools, 

• Dish soap
• Lubricant (grease, or sewing machine/skateboard oil)
• Needle-nose pliers/thin screwdriver
• Socket wrench (½-ich) or ratchet
• Container with a lid
• Acetone
• Paper towels/rags
• T-tools. 

Now you are ready to clean. 

Get the Wheels & Bearings Ready to Clean

To clean the bearings and wheels, you need to remove them from the board. This task is not complete and only requires just a few minutes.

 

Take off the bearings

• First, use a T-tool to remove the nut off the axle. 
• Slide the wheel until the bearing comes out
• Pull the bearing out

Repeat with the other three wheels. Remember to put all the nuts into a container so you don’t lose them.

Note that a spacer may fall out along with the bearings. If it does fall out, store it in the container with the nuts. You will need to put it back later.

Take off the bearings shields

There are two types of bearings shields, one is a simple rubber shield. With this shield, you just have to use a screwdriver to pull it off but be very careful. Otherwise, you will damage it. The other one is a metal shield with a C-clip.

Use a pin to get under the clips, and the shield will pop up easily.

How to clean the bearings

Put everything on a table, and now is the ideal time to clean! Utilize a perfect material or paper towel to clear off any soil on the direction. In the event that you feel the soil can be eliminated effectively manually, the dissolvable isn't required.

Then, to clean the gathered oil, you really want to utilize a specific chemical or a mineral soul, CH3)2CO, or citrus cleaning agent. Pour the compound in a shower jug and splash it in the direction. The splash spout will make the oil

fall off more simply and quickly.

You shouldn't utilize WD-40, as this synthetic will leave a buildup that gathers dust into your course. You unquestionably wouldn't believe this should occur!

On the off chance that you don't have a shower bottle, you will require a container or a compartment with a cover. Put the orientation and the compound together and shake briefly. Then, at that point, take the heading out and wash it under running water. Do this two times to

ensure the oil totally falls off. The dissolvable might be very unforgiving, so make a point to wear gloves to safeguard your hands.

Utilize a paper towel to eliminate the overabundance of water, then utilize a hair dryer to totally dry the course.

The subsequent stage is to grease up the direction. Apply 2-3 drops of skating or sewing machine oil to a slender towel and wipe around the heading. You can apply oil straightforwardly to the course. Recall not to utilize an excessive amount of oil, it will

spread to adjoining parts.

You can purchase oil and oil in your nearby skateboard or bicycle shop, here and there, I can get it in a grocery store. They are quite simple to find!

How to clean electric skateboard wheels

 

Cleaning the wheels is as easy as cleaning the bearings. Follows the steps below:

Process 1: Scrub

Use a rag (or a wire brush/old toothbrush) to scrub around the wheels. Don’t make it too hard or you will scratch the wheel. 

Process 2: Soak

Soak the wheels in warm soapy water for 10 mins

Process 3: Scrub more

After 10 minutes, the dry dust/mud may have softened, use the brush to scrub again to clean the dirt in the smallest nooks and crannies.

Process 4: let the wheel dry for 20 minutes. You can use a hair dryer to make it dry faster.

Reassemble the whole things 

Our cleaning is done, it’s time to put the parts back on and you’re ready to go.

Process 1: Attach the bearings shields. You can use your fingers to snap the bearings into their original place. 

Process 2: Then push the bearings into the wheels. You have to put the bearing divider along with the bearings. Be very careful in this step if you don’t want to be pinched. There are two bearings in a wheel, so you need to put the bearing on both sides of

the wheel. Repeat the process for other wheels.

Process 3: You have to put the wheels back on. Similar to when you disassemble them, now you put them back in their place using a socket wrench to screw the nut back on. Do it until all four wheels are secured in place.

Process 4: Then double-check the wheels and bearings. If the bearings don’t spin freely, then try to move the wheel around. They will snap into place well.

Now that you’re done with everything, try riding around and feel the difference.

Bonus: The Best Mini Electric Skateboard Money Can Buy

So, we have been telling you how to clean the bearings and wheels of your skateboards. In the midst of that, let’s see a skateboard that is providing value for money. 

BASE CAMP Electric Skateboard

If you are looking to buy an electric skateboard that not only provides you the joy of riding a skateboard but also helps you to get from one place to another, it’s this one, the BASE CAMP Electric Skateboard.

Electric skateboards are normally thick because of their electronic parts. But hats off to Base Camp for creating a mini electric skateboard weighing only 5.5kg only.

This skateboard imposes safety for the rider but on itself too. Base Camp has this amazing bash guard attached to the skateboard’s end. This strap makes sure that the kick tail is free from scratches and protects the deck from damage

Furthermore, it can also load a rider as heavy as 220lbs. Therefore, it’s lightweight along with heavy-duty. This skateboard’s 8-layered maple body is an absolute plus. These pieces make the design durable, flexible, and responsive when riding.

This electric skateboard has an abrasive piece of grip tape, the deck holds the skater’s feet firmly. This e-board becomes safer to ride.

This skateboard comes with a carrying backpack, making mobility not an issue for its users.

Powerful Specs:

Price: $332

Battery - 4000 mAh (UL 2272, CE Certified)

Wheels - 90 mm x 51 mm, 85A

Motor - 300w Brushless Single Hub Motor

Recharge - 2-4 Hours

Mode - 4 Speed and Brake Mode

Weight - 5.5 Kg/11 lbs

Range- 9 Miles/14.5 Km

Top Speed- 10 Miles / 16 Km Per Hour

Max Load - 100 Kg/220 lbs

Conclusion

Regular maintenance is essential. You probably won’t get injured just because of old bearings and grimy wheels, but they can give you bad experiences. Good cleaning also makes your board look a lot newer. It is advisable to clean the wheels and bearings every now and then.